How to upgrade node with brew on macOS

I needed to upgrade a wemo Homebridge plug-in on my Mac mini, but before I could node had to upgraded from its current version v14.15.2 to v14.16.1. To find out the current version the mini was running, fire up type the following and press the “enter” key:

node –version

To find out which node versions brew has already installed:

brew search node

My mini had node@10, node@12, and node@14 installed, so I just typed in the following to go to the next version:

brew install node@15

It seemed to install fine, but I found the same output when executing the following command:

brew search node

And, I see what I did wrong, I upgraded to node v15.14.0 based on the following command:

node –version

I’m not sure why brew doesn’t show “node@15” when I search for installed versions of node, but I’ll let it go for now. Also, I should probably start to uninstall some older versions of node, but for now they can stay.

Bluetooth PAN and Big Sur

Back on High Sierra when I wanted to tether my MacBook Pro to my iPhone and save some battery power, I used Bluetooth and chose “Connect to Network” through the Bluetooth icon up in the menu bar. In Big Sur, that changed: when you go to the Bluetooth menu and choose your iPhone, it briefly connects and then disconnects.

I found that the “Connect to Network” option is now buried. Assuming you’ve already paired your iPhone via Bluetooth to your Mac, you can enable Bluetooth PAN using the following:

1. On your Mac, open “System Preferences”.
2. Click “Bluetooth”.
3. Right-click on the name of your iPhone and choose “Connect to Network”.

You’ll now be tethered to your iPhone via Bluetooth PAN. I only do this when I have low bandwidth needs and plan to stay tethered for a long time on battery power. In limited tests with and a tethered Bluetooth connection on Total Wireless, my macbookpro12,1 gets about 0.75 Mbps up and down. When tethering via wifi, the bandwidth jumps to about 40 Mbps down and 7 Mbps up. Finally, tethering via USB was nearly the same as the wifi-tether, although via USB the ping time dropped by 10 ms. This is with crude testing of one sample run for each connection type.

Sideload apps on iPad 4

Riding in the Nemo’s brand new Canyonero was outstanding and I told Liam and Ella all about it. Inspired by the vehicle’s high-tech gadgetry, Liam and I talked about upgrading our New Beetle with a flat panel display. I told him about Adam Bell’s Ignition and mentioned the idea of repurposing our old iPad 4 to the Beetle’s dash. He seemed to be game, so we looked more into it.

By installing a semi-tethered jailbreak and ReProvision, we could keep everything signed on the jailbroken iPad. Unfortunately, our iPad 4 has been upgraded to iOS 10.3.3 and Ignition is only compatible with iOS 8.1, 8.2, and 8.3; while it’s possible to downgrade the iPad’s iOS, we can only get back down to 8.4.1 and Ignition doesn’t run there.

Not easily giving up, we found CarPlay iOS, available through Cydia for $4/license and ventured on. Next step: jailbreak the iPad.

The iPad 4 is 32-bit and Big Sur and Xcode 12.3 only sideload to 64-bit devices. We have a Mac mini still rocking High Sierra and after reviewing this guide we grabbed a 32-bit compatible version of Xcode to side load the iPad 4 jailbreak using these instructions:

  1. Get access to a Mac running High Sierra
  2. Install Xcode 8.3 from here:
  3. Launch Xcode 8.3 and tap Agree on the License Agreement
  4. Connect your iPad to your Mac and, if asked, tap “Trust” on the iPad
  5. In Xcode, choose your iPad as a Build Target, go to Product->Destination->Devices->(choose your device), quit Xcode, and then open Xcode again
  6. Create a new application (File->New->Project…), choose Single View Application, and give it a name (e.g. break) and an identifier (e.g. jail)
  7. Xcode will then ask where you want to save the project, choose the desktop for simplicity
  8. Go to the Xcode menu and choose Preferences…
  9. Click the Accounts button, in the left hand pane click the “+” sign, and add a profile by logging in with your Apple ID (you do not need an Apple Developer account, an iCloud account works fine)
  10. In the right hand pane, you should now see your name followed by “(Personal Team)” with the role “User”
  11. Next, grab the file h3lix-RC6.ipa from here:
  12. Move the downloaded .ipa to your desktop
  13. Next, download this script (or read about patch here)
  14. Move the script to the desktop
  15. In, make the script executable with this command: “chmod +x”
  16. Run the command by typing (without quotes) “./ h3lix-RC6.ipa” and then press enter
  17. Download iOS App Signer, unzip it, and launch iOS App Signer
  18. Drag the .ipa file modified by and drop it on to iOS App Signer’s “Input File” field or click Browse and navigate to the .ipa on your desktop
  19. In iOS App Signer, go to the dropdown menu for Signing Certificate, choose the Apple Development certificate with your name, click “Start”, and iOS App Signer should produce another modified .ipa on your desktop
  20. In Xcode, go to the menubar and click on Window->Devices
  21. Locate your connected device in the list and click the + sign
  22. Choose the file iOS App Signer just created for you
  23. Moving to your iPad, notice an .ipa will appear on your device home screen, but don’t launch it yet
  24. Tap Settings->General->Device Management
  25. Find and tap the new profile
  26. Tap “Trust” and the .ipa you installed can now be tapped

To keep the jailbreak intact, we also installed ReProvision through Cydia. Fire up, go to Sources->Edit->Add, enter “”, and tap “Add Source”. In Sources, tap Matchstic->System->ReProvision->Install. From the home screen of your iPad, tap “ReProvision” and on the right hand side of the screen and “h3lix” as an app to sign and then tap “Sign”. It will take a minute or so, but eventually ReProvision will sign the app and then continue to sign the app when it is within 2 days of expiring.

macOS Server and Wildcard Certificates

In a bid to bring automatic wildcard renewal of SSL letsencrypt certificates to my Mac mini running macOS Server, I used Eric’s instructions and only tweaked one line in the section “Creating the certificate” by changing this line:

sudo certbot certonly –standalone -d

to this line:

sudo certbot certonly –manual –preferred-challenges=dns –email –server –agree-tos -d *

When –preferred-challenges=dns is used, I had to create a TXT record with my registrar, but after you doing this once for each domain it shouldn’t be necessary again. I’ll report back when I know the rest of Eric’s scripts are working.

Curt 18085 and Frame Rub Workaround

I have yet to bring our fat bikes anywhere by car with a new Curt 18085 bike rack we picked up for two reasons:

1. We need to pick up the tensioning strap that takes some bounce out of the rack
2. The rack has padded arms that hold the frame and I’m concerned about potential frame rub

To fix #1, I’ll pick up Curt’s recommended 18050 strap. For #2, the cheapest workaround may be to identify what part on the bike frame will contact the rack’s padded arm, clean the bike frame’s identified area, and then place a frame sticker/piece of packing tape on the identified frame area before loading it into the rack. Fortunately, I’ve got a bunch of large frame stickers that I picked up cheap on eBay that I can burn for this task. I’ll report back on how it works in the wild.

Surly Big Dummy, Yokozuna, and Rohloff Speedhub

After using a tandem cable kit set that wasn’t quite long enough, Merry Sales’ Jim Porter kindly helped identify Rohloff Shifter Cable Set 63640 (UPC 0899430044112) to get my Rohloff twist shifter mated with a Speedhub 500/14 on my XL frame Big Dummy, which has a bit extra length as previously mentioned.

Prior to this post, my Dummy had Rohloff shift housing and cables installed, which are adequate, but after enjoying Yokozuna’s strong Reaction brake housing and cables I knew I had to try their shift housing and cables. On the Big Dummy’s long cable run, the compressionless brake housing brings responsiveness I haven’t seen in other housings and I’m hoping for something similar with Yokozuna’s shift housing and cables.

Installation goes just like any other cable and I used Rohloff’s how-to video for installing the cables to the twist shifter and supplementary video for an external mech setup.

First thing I noticed after pulling the Yokozuna Shifter Cable Set from the packaging is that the housing has a smaller diameter than Rohloff’s cables, so much that I had to measure the difference: Rohloff housing has a 4.8 mm diameter and Yokozuna has a svelte 4.1 mm diameter. I didn’t weigh the two, but I’d expect a difference.

To fit the cable housing to the Dummy, I ended up cutting 50 mm of housing from the lengths provided by Yokozuna, I aimed for twin 2250 mm housing lengths and this proved useful, as I later had to switch the cable positions around and cut off another centimeter.

After getting the cables on the Dummy in my shop and running through the gears, I can already say I’ve never felt my Rohloff shift through gears this smoothly. I’ll verify this with the Dummy out on the road tomorrow and come back with an update, but I’m already tickled to now have Yokozuna on my front brake and shifter. Note, a future post might be when I’m able to return Yokozuna to the rear brake, which is where the most noticeable benefit is seen on this bike – I expect to do this when I replace the rear caliper after this winter.

I’ll pass this back to Merry Sales, but the set includes cable caps and these are superfluous to Rohloff internal and external mechs.

** Update 12-4-2020 **
I’ve ridden the Dummy a few times now and will re-state how smooth and easy shifting is with Yokozuna shift housing and cables. I’m hoping this holds up!

OpenCore 0.6.3 and macpro5,1

My son has been using Catalina on his 2009 Mac Pro (macpro4,1), firmware upgraded to a macpro5,1 over a year ago. Catalina and OpenCore 0.58 along with his RX580 4GB have been excellent. He can select any of his 4 disks at boot time through a graphical user interface and OpenCore helps with system updates by tricking Apple’s software into believing your Mac is no different than a natively supported machine.

With Big Sur now available and OpenCore at 0.63, he was ready to upgrade his Mac. We backed up his data and proceeded to follow these instructions, everything through Part I seems to be running fine. Will report back after we update through Parts II and III. Also, unless things have changed with the instructions above, this video found from this forum shows how to modify the EFI so that Big Sur can be updated – note, the instructions in this video should be reversed when you are done with Apple’s updates and you want to optimize speed of your Mac Pro. Also note, we were spared from having to mess with Clover to enable the onboard ethernet through the Intel Mausi Kext, I believe the config.plist file linked within the instructions above helps to enable this for Mac Pro hardware.

Last note for now: we find that Clover Configurator works well for mounting the EFI and also, the drive in the SATA bay seems to contain the EFI that needs editing, not the EFI on the NVMe SSD. If we had removed the SATA drive from the Mac Pro, the NVMe’s EFI would probably be the main drive initiating OpenCore at boot time.

Toro Powerlite CCR Not Starting

My “snowpup” wouldn’t fire up today to hit a few inches of fresh stuff that landed and that was disappointing, as 4 days earlier when it was 70 degrees it fired up just fine.

I committed a few errors from last winter:

1. I left treated gasoline in the tank.
2. I may not have pulled the cord until there was minor tension to seal off the intake valve.

After pulling 50 times, I figured I checked the gas tank and it was mostly empty. I topped the tank with fresh fuel, 50:1. I went to start it again and no dice. I pulled the spark plug out and it was soaked in fuel. Ugh. Dried the spark plug tip and put it back in. Pulled the cord, still nothing. Figuring something else was wrong, I brought it into the trusty Schwie Shop in the basement.

After a few hours of warming up, I pulled the bottom cover off (2 screws!) and found another problem. The primer hose broke off just behind the bulb. Argh. Worse, the primer line was leaking fuel out the broken end. Surely this is contributing something to the problem. For now, I’m putting a small binder clip on the end of the hose and I’ll order one of these:

44-2750 Body – Primer

While tinkering inside the motor area, I remembered the choke was flinging back and forth last winter. Looking at the parts list it appears the choke is missing a few parts:

632169 Spring – Throttle Return
631184 Washer – Steel
631183 Washer – Felt

Next, I wanted to see if the snow blower was making a spark, so I removed the spark plug, reattached the plug wire, laid the tip of the plug so it was touching the outside of the motor, turned out the lights in the shop, and gently pulled the cord. Boom, a blue spark jumped across, yes! That means I don’t a plug or a plug wire, so I reassembled the machine and brought it out to the garage. First pull and it fired up!

Now, there were several things wrong with this snowblower and some conditions changed, including warming it up to room temperature. I’m still in the process of the repairs as I’ll need to get more parts, but here’s my weak connection of dots as to why it worked 4 days ago and suddenly didn’t today:

I pulled the snowblower out of the garage attic where it was stored on all 4 wheels, brought it outside, fired it up, turned it off, and then hung it by its handle inside the main part of the garage (mind you, last winter’s treated gas was still inside). Jump to today, I take it off the hook in the garage and try to fire it up, nothing. I think what happened was last year’s residual fuel doesn’t want to combust when its cold, but it’s willing to when it’s a few degrees warmer. To test this theory, I’ll run out to the garage tomorrow morning and give it a pull. If it fires up, I’m going to chalk it up to the fact that the old fuel is now burned out and mixed with enough new fuel that its willing to combust. If it doesn’t start up, it’s because I haven’t run it long enough to combust all the fuel in the hose. More later…

** Update 11-16-2020 **

I pulled started the snowblower a couple more times over the next couple days and it started with fewer and fewer pulls until it started with a single pull, I’m pretty sure the cause was old gas in the line.

I went looking to purchase individual parts to make the above repairs and it came to about $20 in parts, so I ended up purchasing a carburetor assembly for $12.95 shipped from Amazon. Will install that soon to fix the broken primer bulb body and loose choke handle – the new carburetor seems to be built better than the original.

AEG18LII-VV String Specifications

My kids are both left-handed and they each have a sweet Ibanez guitar, AEG18LII-VV. My son broke a string recently and when I attempted to look up string specifications at, nothing appeared and these are pretty new guitars.

After calling Ibanez, the helpful rep said that specifications for this guitar are not listed their website, because it was manufactured as a proprietary model; however, he said specs for the AEG18L and -19L are similar. He said the guitar could use a string kit that ranges from 12-53 or 12-54, with the individual gauges being:

12, 16, 24, 32, 42, and 53

He said kits may be marketed under the following makes:

D’Addario – acoustic light – EJ16
Elixir – light

And I went with a set of the D’Addario strings this time around.

VG6250T76NV and Flexible Anode Replacement

I should have replaced our American Hot Water Heater VG6250T76NV’s magnesium anode years ago – COVID continues to give me a chance to catch up. Note: I’m assuming this water heater shipped with a magnesium anode, not an aluminum anode.

I measured the distance above my hot water heater and while my installation may allow clearance to fit an OEM 32-inch anode, it seems it will be very tight and may not fit. After watching an excerpt from This Old House, I learned about a collapsible or flexible anode that has been developed, so I’ll go that route so I don’t have to try and move plumbing out of the way.

If I had selected the non-flexible OEM part number, sold by a local supplier, Dey Appliance, they recommended this part calling for a 32-inch length anode with 3/4″ NPT, and 0.84-inch diameter. Ultimately, I selected an ApplianPar flexible magnesium anode, mostly because its close to meeting the specifications and is readily available – yes, its a bit narrower, but I’m fine to replace the anode more often from now on – shame on me for waiting this long.I’ll update this post after I install it tomorrow, assuming I can get the old one out, which worries me a bit. Which reminds me, I need to pick up a 1 1/16 inch socket!

** Update 10-2-2020 **
Dad loaned me his 1 1/16 socket (thanks Grandpa Don!) paired with his Campbell Hausfeld impact wrench. I used this combo in lieu of my Makita LXDT04 impact driver, which produces less than 1,000 kg/cm to the Campbell Hausfeld’s ~3,000 kg/cm, hello!

The old anode (far left in picture, below) backed out in less than a minute and with it came a load of scale from 10 years of build up, see photo below. Notice that the top of the old anode bent a little bit on its way out as very little magnesium remained, which made removing it even easier. Because of it bending on the way out and my previous measurements, I think it was the right call to go with a flexible anode for the replacement. Trying to get the flexible anode to screw in is a little challenging, but it seemed to snug up with only a turn or two. I was a little concerned about that, but after turning the water back on there are no leaks at the anode’s hex fitting.

After seeing the amount of scale on the old anode, I’m beginning to think I might need to reconsider softening my water. Saint Paul water is reportedly 5-6 grains of hardness, which MPCA classifies as “moderately hard”. The anode’s scale build up makes me question the condition of the copper pipe I installed to replace the galvanized cast iron piping shortly after we moved in 20 years ago. I’m guessing there will be more on this in a future post.

While researching this, I may need to take Merles up on their offer for a free lead test.